HDD 204 - Heavy Duty Diesel BrakesCredits: 4
Introduces and practices the inspection and maintenance of hydraulic, mechanical and ellectrical braking systems for heavy duty diesel vehicles. Practices NATEF tasks related to hydraulic, mechanical and electrical braking systems for heavy duty diesel vehicles.
Prerequisite(s): HDD 106 with a minimum grade of "C" (2.0)
Corequisite(s): HDD 151 and HDD 156 .
Lecture Hours: 65 Lab Hours: 40
Meets MTA Requirement: None
Pass/NoCredit: Yes
Outcomes and Objectives 1. Complete heavy duty diesel NATEF tasks related to Air Brakes as listed
A. Air Supply and Service Systems
1. Identify poor stopping, air leaks, premature wear, pulling, grabbing, dragging, or balance problems caused by supply and service
system malfunctions; determine needed action.
2. Check air system build-up time; determine needed action.
3. Drain air reservoir/tanks; check for oil, water, and foreign material; determine needed action.
4. Inspect air compressor drive gear, belts and coupling; adjust or replace as needed.
5. Inspect air compressor inlet;; inspect oil supply and coolant lines, fittings, and mounting brackets; repair or replace as needed.
6. Inspect and test air system pressure controls: governor, unloader assembly valves, filters, lines, hoses, and fittings; adjust or replace
as needed.
7. Inspect air system lines, hoses, fittings, and couplings; repair or replace as needed.
8. Inspect and test air tank relief (safety) valves, one-way (single) check valves, two- way (double) check valves, manual and automatic
drain valves; replace as needed.
9. Inspect and clean air drier systems, filters, valves, heaters, wiring, and connectors; repair or replace as needed.
10. Inspect and test brake application (foot/treadle) valve, fittings, and mounts; check
pedal operation; replace as needed.
11. Inspect and test stop light circuit switches, wiring, and connectors; repair or replace as needed.
12. Inspect and test hand brake (trailer) control valve, lines, fittings, and mountings; repair or replace as needed.
13. Inspect and test brake relay valves; replace as needed.
14. Inspect and test quick release valves; replace as needed.
15. Inspect and test tractor protection valve; replace as needed.
16. Inspect and test emergency (spring) brake control/modulator valve(s); replace as needed.
17. Inspect and test low pressure warning devices, wiring, and connectors; repair or replace as needed.
18. Inspect and test air pressure gauges, lines, and fittings; replace as needed.
B. Mechanical/Foundation Brakes
1. Identify poor stopping, brake noise, premature wear, pulling, grabbing, or dragging problems caused by the foundation brake, slack
adjuster, and brake chamber problems; determine needed action.
2. Inspect and test service brake chambers, diaphragm, clamp, spring, pushrod, clevis, and mounting brackets; repair or replace as
needed.
3. Identify type, inspect and service slack adjusters; perform needed action.
4. Inspect camshafts, tubes, rollers, bushings, seals, spacers, retainers, brake spiders, shields, anchor pins, and springs; replace as
needed.
5. Inspect, clean, and adjust air disc brake caliper assemblies; determine needed repairs.
6. Inspect and measure brake shoes or pads; perform needed action.
7. Inspect and measure brake drums or rotors; perform needed action.
C. Parking Brakes
1. Inspect and test parking (spring) brake chamber diaphragm and seals; replace parking (spring) brake chamber; dispose of removed
chambers in accordance with local regulations.
2. Inspect and test parking (spring) brake check valves, lines, hoses, and fittings; replace as needed.
3. Inspect and test parking (spring) brake application and release valve; replace as needed.
4. Manually release (cage) and reset (uncage) parking (spring) brakes in accordance with manufacturers' recommendations.
5. Identify and test anti compounding brake function.
2. Complete heavy duty diesel NATEF tasks related to Hydraulic Brakes as listed below.
A. Hydraulic System
1. Identify poor stopping, premature wear, pulling, dragging, balance, or pedal feel problems caused by the hydraulic system; determine
needed action.
2. Inspect and test master cylinder for internal/external leaks and damage; replace as needed.
3. Inspect hydraulic system brake lines, flexible hoses, and fittings for leaks and damage; replace as needed.
4. Inspect and test metering (hold-off), load sensing/proportioning, proportioning, and combination valves; replace as needed.
5. Inspect and test brake pressure differential valve and warning light circuit switch, bulbs/LEDs, wiring, and connectors; repair or replace
as needed.
6. Inspect disc brake caliper assemblies; replace as needed.
7. Inspect/test brake fluid; bleed and/or flush system; determine proper fluid type.
B. Mechanical/Foundation Brakes
1. Identify poor stopping, brake noise, premature wear, pulling, grabbing, dragging, or pedal feel problems caused by mechanical
components; determine needed action.
2. Inspect and measure rotors; perform needed action.
3. Inspect and measure disc brake pads; inspect mounting hardware; perform needed action.
d.Check parking brake operation; inspect parking brake application and holding devices; adjust and replace as needed.
4. Check parking brake operation; inspect parking brake application and holding devices; adjust and replace as needed.
C. Power Assist Units
1. Identify stopping problems caused by the brake assist (booster) system; determine needed action.
2. Inspect, test, repair, or replace hydraulic brake assist (booster), hoses, and control valves; determine proper fluid type.
3. Check emergency (back-up, reserve) brake assist system.
3. Complete heavy duty diesel NATEF tasks related to Air and Hydraulic Antilock Brake Systems (ABS) and Automatic Traction Control
(ATC) as
A. Observe antilock brake system (ABS) warning light operation (includes trailer and dash mounted trailer ABS warning light); determine
needed action.
B. Diagnose antilock brake system (ABS) electronic control(s) and components using self-diagnosis and/or electronic service tool(s);
determine needed action.
C. Identify poor stopping and wheel lock-up problems caused by failure of the antilock brake system (ABS); determine needed action.
D. Test and check operation of antilock brake system (ABS) air, hydraulic, electrical, and mechanical components; perform needed action.
E. Test antilock brake system (ABS) wheel speed sensors and circuits; adjust or replace as needed.
F. Bleed the ABS hydraulic circuits.
G. Observe automatic traction control (ATC) warning light operation; determine needed action.
H. Diagnose automatic traction control (ATC) electronic control(s) and components using self- diagnosis and/or specified test equipment (scan
tool, PC computer); determine needed action.
I. Verify power line carrier (PLC) operations.
4. Complete heavy duty diesel NATEF tasks related to Wheel Bearings as listed below.
A. Clean, inspect, lubricate and replace wheel bearings and races/cups; replace seals and wear rings; inspect spindle/tube; inspect and
replace retaining hardware; adjust wheel bearings. Verify end play with dial indicator method.
B. Identify, inspect or replace unitized/preset hub bearing assemblies.
Add to Portfolio (opens a new window)
|