May 21, 2024  
2018 - 2019 Catalog 
2018 - 2019 Catalog [ARCHIVED CATALOG]

Add to Portfolio (opens a new window)

ASEP 151 - Engine Repair Level 2

Credits: 1
Practices the service and repair of gasoline internal combustion engines. Practices NATEF tasks to AST (Automotive Service Technology) level related to gasoline engines. Requires meeting all related GM ASEP training requirements. Note: Student must complete necessary paperwork for state of Michigan Automotive Repair Training Permit.

Prerequisite(s): ASEP 101  and ASEP 149 .
Corequisite(s): None
Lecture Hours: 15 Lab Hours: 25
Meets MTA Requirement: None
Pass/NoCredit: No

Outcomes and Objectives
  1. Complete Level 2 NATEF tasks related to general Engine Repair as listed below.
    1. Complete work order to include customer information, vehicle identifying information, customer concern, related service history, cause, and correction.
    2. Research applicable vehicle and service information, such as internal engine operation, vehicle service history, service precautions, and technical service bulletins.
    3. Verify operation of the instrument panel engine warning indicators.
    4. Inspect engine assembly for fuel, oil, coolant, and other leaks; determine necessary action
    5. Install engine covers using gaskets, seals, and sealers as required.
    6. Remove and replace timing belt; verify correct camshaft timing
    7. Perform common fastener and thread repair, to include: remove broken bolt, restore internal and external threads, and repair internal threads with thread insert.
    8. Inspect, remove and replace engine mounts.
    9. Identify hybrid vehicle internal combustion engine service precautions.
  2. Complete Level 2 NATEF tasks related to Cylinder Head and Valve Train as listed below.
    1. Remove cylinder head; inspect gasket condition; install cylinder head and gasket; tighten according to manufacturer's specifications and procedures.
    2. Clean and visually inspect a cylinder head for cracks; check gasket surface areas for warpage and surface finish; check passage condition.
    3. Inspect pushrods, rocker arms, rocker arm pivots and shafts for wear, bending, cracks, looseness, and blocked oil passages (orifices); determine necessary action.
    4. Adjust valves (mechanical or hydraulic lifters).
    5. Inspect and replace camshaft and drive belt/chain; includes checking drive gear wear and backlash, end play, sprocket and chain wear, overhead cam drive sprocket(s), drive belt(s), belt tension, tensioners, camshaft reluctor ring/tone-wheel, and valve timing components; verify correct camshaft timing.
    6. Establish camshaft position sensor indexing.
  3. Complete Level 2 NATEF tasks related to Engine Block Assembly as listed below.
    1. Remove, inspect, or replace crankshaft vibration damper (harmonic balancer).
  4. Complete Level 2 NATEF tasks related to Lubrication and Cooling Systems as listed below.
    1. Perform cooling system pressure and dye tests to identify leaks; check coolant condition and level; inspect and test radiator, pressure cap, coolant recovery tank, and heater core; determine necessary action.
    2. Identify causes of engine overheating
    3. Inspect, replace, and adjust drive belts, tensioners, and pulleys; check pulley and belt alignment.
    4. Inspect and test coolant; drain and recover coolant; flush and refill cooling system with recommended coolant; bleed air as required.
    5. Inspect, remove, and replace water pump.
    6. Remove and replace radiator.
    7. Remove, inspect, and replace thermostat and gasket/seal.
    8. Inspect and test fan(s) (electrical or mechanical), fan clutch, fan shroud, and air dams.
    9. Perform oil pressure tests; determine necessary action.
    10. Perform engine oil and filter change.
    11. Inspect auxiliary coolers; determine necessary action.
    12. Inspect, test, and replace oil temperature and pressure switches and sensors.

Add to Portfolio (opens a new window)